Saturday, February 20, 2010

heater

How to Install Gas Space Heaters Tips

Introduction

Gas space heaters are very useful. They can provide extra heat on very cold days and they can be counted on during power outages. Gas space heaters can help you save money because they run on gas, a cheaper energy source than electricity. Be sure to use your heater in a well ventilated room. Follow all of the manufacturer’s instructions when installing your gas heater and be sure to adhere to any of your town’s building codes.

Difficulty: Moderately Difficult

Things You'll Need:

- Stud finder

- Piping

- Thread sealant

- Pressure gauge

- Spray bottle filled with dish soap and water

Instructions

Step 1

Buy a heater. Do not purchase a heater that is too big for the room you will be placing it in. Check the heater’s box for a sizing table or ask a sales assistant at the store for their help.

Step 2

Check that there will be plenty of fresh air and ventilation in the room that will house the space heater. Put the heater in a room that has windows. Keep the windows open about half an inch when running the heater.

Step 3

Place the heater on an even surface. The heater needs to be out of pedestrian’s way. Keep heaters away from curtains, walls, decorations, and furniture. Put the heater close to an outlet because most heaters need to be plugged in.

Step 4

Use a stud-finder to search the wall for a stud or check the floor for a joist. Attach the mounting brackets that came with the heater to the stud or floor joist.

Step 5

Shut off your gas supply. Find piping in your basement or a crawl space. Install gas supply piping by “T”ing into the existing piping. Install a shut-off valve and sediment drain into the piping. Apply a small amount of pipe thread sealant to the pipe. Use a sealant that works with your fuel type. Check that the pressure coming from your gas supply is not too high using a pressure gauge.

Step 6

Inspect the new piping for leaks by spraying a mixture of dish soap and water onto each joint. If you spot growing bubbles on a joint, you will find a leak in that location. The leak needs to be sealed.

Step 7

Attach your heater to the gas piping while the heater is off. Check the pipes for leaks again. You may want a building inspector to do a final check of the heater and the piping before you use your new heater.

Tips

Shut the door to the room that the heater is in to keep the room warm.

Purchase a heater that has all the current safety features such as the ability to turn itself off if it gets knocked over. You will know that the heater’s safety features are up to date if you see the Underwriter’s Laboratory (UL) label on the heater.

Warnings

Badly crafted or operated heaters can cause fires so be very careful when using a gas space heater.

Never leave a heater on while you leave the room or go to sleep.

New York State Department of Health: Supplemental Space Heaters

http://www.health.state.ny.us/environmental/indoors/heaters/

Wednesday, February 17, 2010

repo car

How to Find Repossessed Vehicles to Buy

Introduction

Repossessed cars are no longer all that hard to find. Newspapers and web searches will turn up a number of results. Repo cars are usually cars that were impounded by the police or collected by the bank from people who couldn’t pay their loans back. Repossessed cars are sold at reduced prices so they can be in demand. Repo cars can be sold by public banks or in private auctions. Just be careful to inspect the car well so that you do not get ripped off.

Difficulty: Easy

Instructions

Step 1

Locate cars that have been repossessed before they are given over to be sold at a public auction or sale. Try calling your local banks or credit union. Often they can give you a recent list of cars that were repossessed.

Step 2

Check the newspaper, websites, and the phone book for repo cars. Try looking in the newspaper under the auto classifieds column for public auctions. Search the eBay motors site for cheap repo cars.

Step 3

Figure out how you are going to pay for the car. Repo car sellers want to complete sales quickly so you need to have either proper financing, cash, or certified funds easily accessible. Apply to be approved from your bank or credit union before you try to buy a car.

Step 4

Look up how much a repo car should cost in the model that you want. You can find this information in the NADA Guide or the Kelley Blue Book. Repo cars should be much cheaper than new cars.

Step 5

Examine in person the car that you have chosen. Check its mileage. Get a vehicle history report from Car Fax or Auto Check so you can see whether the car has been in an accident or not. You should also take the car to be checked by a mechanic. If everything checks out, purchase the car.

Tip

Try to take the car for a test drive before you purchase it.

Warning

Read the fine print of the contract that will make you the new owner of a repo car because the contract can include hidden fees, warranty information, and other problems.

Ebay Motors

http://www.motors.ebay.com/

Ezine @rticles: How To Locate Repossessed Vehicles For Sale

http://ezinearticles.com/?How-To-Locate-Repossessed-Vehicles-For-Sale&id=975071

rails

How to Install Wood Hand Rails

Introduction

Deck handrails can serve as decoration for a deck. Handrails can also make the deck safer for people walking down the deck stairs. This project does not require a lot of woodworking expertise. The handrails can be as nice or as unadorned as you like. Make sure you have the proper tools before beginning work. You will be working outdoors so you may want to install the hand rails on a day that has good weather.

Difficulty: Moderately Difficult

Things You'll Need:

- Measuring tape

- Lumber

- Pencil

- Carpenter’s square

- Studs

- Electric miter saw

- Deck screws

- Screwdriver

- Carpenter’s level

Instructions

Step 1

Determine the perimeter of the deck. Write down the measurement. Figure out the amount of short pieces you will need by dividing the perimeter of the deck by how long your piece of your lumber is.

Step 2

Fit two rows of lumber along the perimeter. This will be the bottom and top of the handrail. Work your way around the lumber and draw a mark every 16 inches. Then put the carpenter’s square on top of the marks and pencil in a line across each mark. Draw an “X” by the side of every mark. This is where you will install the studs.

Step 3

Count how many studs you will need and cut the studs that you need to the height that you want your handrail to be. Use an electric miter saw to cut the studs. Don’t forget to add in two extra studs that you will attach the handrail to. These studs will be placed in the corners.

Step 4

Position the studs in the places that you previously marked for them. Attach the studs to the bottoms and tops of the handrail. Use deck screws to attach the studs.

Step 5

Pick the handrails up. Place them in the spot on the deck that needs handrails. Hold them in place with deck screws. Use a carpenter’s level to examine the handrail corners. Also inspect the ends that affix at the house.

Tip

Check out the building codes in your neighborhood so that you can build handrails that meet the town requirements.

Warning

Safety equipment, such as safety goggles, needs to be worn when working with wood.

Floating Foundation Deck System: How to Install a Wood Railing with Posts

http://www.deckplans.com/how-to-install-wood-handrail-posts

movado

How to Recognize a Knock Off Movado

Introduction

Knock of Movado watches are relatively easy to spot. They have a number of flaws that you can look for. Most Movado watch counterfeits are made by foreigners. They are not looked over by any sort of quality control group. Therefore, they have mistakes that you will notice and therefore you will be able to recognize a fake Movado from a genuine Movado watch. These mistakes will include incorrect printing and contamination to the watch itself.

Difficulty: Easy

Things You'll Need:

- Jeweler’s loupe

Instructions

Step 1

Look for spelling and grammatical errors. Most counterfeit Movado watches are made by foreign workers. Therefore, spelling errors are common. Carefully go over all words on the watch because the smallest of mistakes can give the watch away as a fake.

Step 2

Examine the surface of the dial for dust, fingerprints, and hair. There should be none of these on real Movado watches. If you find any dust, fingerprints, or hair, you can be pretty sure that you have found a fake Movado watch.

Step 3

Check the logo. Movado copies may have the logo glued onto the end of the crown. Inspect the crown for signs of uneven edges or glue.

Step 4

Inspect the dial and date wheel with a jeweler’s loupe. All the printing should be clear and sharp. There should not be any fuzzy edges or blending of letters. A watch with any irregular print would never have made it out of the factory.

Tip

A real Movado watch will wind up smoothly. You should not be able to feel movement in the case.

shower

How to Troubleshoot a Showerhead

Introduction

There are two main issues to look for when dealing with a faulty showerhead. Check for a leaky showerhead or a clogged showerhead. Leaky showerheads can occur when there is a worn washer or a break in the connection between the shower arm and the showerhead. When showerhead holes get clogged, water backs up and leaks out. Different shower models can have various problems and solutions so find out what works best for your own specific shower.

Difficulty: Moderately Easy

Things You'll Need:

- Scale remover/white vinegar

- Toothpick/small nail

- Stiff plastic brush

- Plumber’s tape

- New washer

- Wrench

Instructions

Step 1

Find the problem. Leaks can be found at the place where the pipe is screwed into the showerhead. You will also need to check for a clogged showerhead.

Step 2

Unscrew the showerhead in the counterclockwise direction. This might displace lime buildup or rust. Check the threads on the head and the arm for cracks.

Step 3

Clean the head and the arms with scale remover or white vinegar to remove rust. Leave the cleaner to sit on the shower pieces for a few hours. Wait for the pieces to dry completely.

Step 4

If the showerhead holes are clogged, remove the faceplate by unscrewing the screws that secure the faceplate to the head. Soak the faceplate in white vinegar. Leave the faceplate in the vinegar for no less than eight hours.

Step 5

Stick a toothpick or a small nail through each hole in the showerhead. This will remove all buildup from the holes. Use a stiff plastic brush to scour the faceplate. Put the faceplate back into place.

Step 6

Wrap plumber’s tape over the shower arm threads in a clockwise direction. If there is a washer in the shower arm, replacing the washer can also fix leaks. Tighten the showerhead back into place.

Tip

Use a pipe wrench to unscrew stubborn showerheads.

Home Addition Plus: How to Fix a Leaking Showerhead Faucet

http://www.homeadditionplus.com/How%20to%20Fix%20a%20Leaking%20Showerhead%20Faucet.htm

Showerhead Resource: Dealing With a Leaky Shower Head

http://www.showerheadresource.com/dealing-with-a-leaky-showerhead/

Tuesday, February 16, 2010

solar

How to Make a Solar Collector Cheap

Introduction

If you want to heat water by the sun and you don’t want to spend a lot of money doing it, this is the perfect project for you. Most of the materials can be found in your local garbage dump. Building this solar collector will allow you to learn about how the sun heats water. Also, you will be using a renewable energy source to heat the water which is really great for the environment.

Difficulty: Difficult

Things You'll Need:

- The back of a refrigerator

- Wood

- A pane of glass

- Saw

- Half a door mat

- Aluminum Foil

- Pump hose

- Duct tape

- Screws

- Screwdriver

- 2 buckets

- Water

Instructions

Step 1

Find a back from a fridge. Get the Freon (type of coolant) removed. Cut near the coolant holder to remove the grill from the base.

Step 2

Build a frame for the solar collector. The frame is held on by building a similar frame on the back and driving large wood screws through the front frame, the backing and into the back frame. I added some foil to the backing.

Step 3

Seal all cracks and secure the foil into place with duct tape

Next we cut some notches for the entry and return ports to the collector. Note again the use of duct tape to seal cracks.

Step 4

I got some air pump hose from the local fish store and attached them to the end of the entry and return ports.
The duct tape was applied to make sure it was a tight fit, it was later removed as it was not needed.

Step 5

Use the fridge’s mounting brackets and duct tape to attach the collector onto the backing. Tape or screw the pane of glass to the top to trap the heat. Tape is the cheaper but less lasting option.

Step 6

Place the panel on an angle. This will allow more sunlight to catch onto the panel. Place one end of the hose into the bottom of a container of cold water. Take the other end of the hose and suck on it until a little water comes out. Use gravity to flow the cold water into the heater by putting the cold water container higher than the warm water collector.

Tip

You can heat up the water to higher temperatures by reheating the already heated water.

Warning

Be careful not to burn yourself because the water heats to temperatures of about 110 degrees.

Build It Solar: The Renewable Energy site for Do-It-Yourselfers

http://www.builditsolar.com/



roof

How to Repair a Leaky Flat Roof

Introduction

The most important part of fixing a leaky roof is finding the source of the leak. You will need to look over the entire roof very closely and carefully. Be especially thorough because it would be a shame if you had to go through the entire process again if you didn’t repair every potential leak source the first time. Once you identify the problem areas, you will be ready to make the necessary repairs. Make sure you are not afraid of heights before attempting this project because you will be on top of your roof.

Difficulty: Difficult

Things You'll Need:

- Binoculars

- Weighted markers

- Flashlight

- Roofing cement

- Trowel

- Heavy-duty razor or carbide blade

- Patching fabric

- Rag

Instructions

Step 1

Look very thoroughly at your entire roof with binoculars. Check for tears, cracks, rotting areas, missing sheathing, and any other potential issue. Also make sure that there are no breaks in material such as no spaces between the brick of the chimney and the roof sheathing.

Step 2

Go on the roof and put a weighted object by each problem spot that you found. Walk along the roof and inspect every area up close. Mark any other problem areas that you find with weighted objects.

Step 3

Go into your attic. Check for any potential water trails with a flashlight. If you find any, follow them up to where they hit the ceiling and push a nail at that point so you can easily find the problem spot when you get back onto the roof.

Step 4

Repair cracks in the sheathing. Clean the crack by scraping away any dirt. Cover the crack with roofing cement and use a trowel to cover the crack completely. Push a piece of roof patching fabric deep into the cement. Repeat Step 4 for all cracks.

Step 5

Repair bubbles in the sheathing. Use a heavy-duty razor or a carbide blade to cut an “X” into the bubble. Pull up the sides of the cut sheathing. Empty the area underneath the bubble of debris and soak up excess moisture with a rag. Let the bubble dry in the sun for a few hours. After that, put some cement under the sides of the sheathing and flatten the area. Apply a layer of cement and cover it with patching fabric and then another layer of each. Finish with a last layer of cement. Spread the cement into the sheathing. This will allow for drainage. Repeat Step 5 for all bubbles.

Step 6

Repair breaks in materials such chimney bricks and roof sheathing. Clean the area and remove old pieces of cement that may become irksome. Work a layer of cement between the roof feature and the sheathing. Spread the cement into the sheathing. This will allow for drainage. Repeat Step 6 for all breaks.

Tip

Rub penetrating oil like WD40 onto your hands to remove roofing cement.

Warning

Be thorough when searching for water trails because they can be tricky and curvy.